變頻螺桿式冷水機運行前的檢查項目，電源及電控儀表系統的檢查。開機前檢查配電容量是否與機組功率一致，選擇的電纜線徑是否能承受主機的大工作電流。檢查電氣系統是否與機組一致。機組電氣系統為三相五線制（三相線，一根零線，一根地線，380V±10%）。檢查壓縮機電源線是否連接良好。如果松動，請重新擰緊。壓縮機接線處使用的扭矩為500kg cm。由于主機的長途運輸和吊裝，螺釘可能會松動。否則可能會損壞主機控制柜和壓縮機內的電氣元件（如空氣開關、交流接觸器等）。用萬用表仔細檢查所有電路，看接線是否正確；用兆歐測量，確保外殼沒有短路；檢查接地線是否正確安裝，對地絕緣電阻是否大于2MΩ；檢查電源線是否滿足容量要求。檢查是否在設備的電源線上安裝了斷路器。

    控制柜內主電路的所有接線和控制電路的外部接線在通電前都應對照接線圖進行全面檢查（如曲軸箱油加熱器接線、壓縮機電子保護器、循環水溫度傳感器、目標流量開關、水泵聯合控制等）；檢查端子螺栓是否緊固無松動。檢查電控儀表、電器是否安裝正確、完整、有效，電控柜內外，特別是各點接線口是否清潔、無雜物。檢查以上各項后，當控制柜通電時，電源指示燈亮。這時，油加熱器開始工作。觀察相序保護器是否正常。如果相序保護器正常（綠燈亮），閉合控制柜內的單*開關（QF2），控制電路開始工作。觸摸屏（文字顯示）和PLC控制器全部投入運行。